The EP Series Helical Bevel Reducer provides unmatched performance, durability, and design flexibility. This unit offers torque capacities up to 20,000 Nm (14,750 ft pounds).
The cat4CAD software enables simple interactive product collection of the entire gearbox and gear-engine system. Cat4CAD supports you in choosing and configuring these products, gives you the chance to print out intensive technical data linens, and generates complete 2D drawings and 3D models for direct download.
11 sizes
Input power capacities from 0.16 to 120 HP
Gear ratios from 5:1 to 8900:1
Torque capacities to 20,000 Nm
Inverter duty class F insulated motor windings
Course 12 Helical and Spiral Bevel Gears: Provides higher efficiencies and better torques in smaller sizes.
Multiple Input Options: Essential gear motors, inch or metric shafts, NEMA, IEC, and servo adapters provide unmatched drive versatility.
Multiple Output Choices: Hollow bores and shrink disks for shaft mounting, inch and metric output shafts, installation pilots and flanges offer an array of design solutions.
UNIBLOCK Housing: For maximum rigidity, universal installation on five sides or with a torque arm.
Worldwide Electric motor: Multiple leads and windings for globally multi volt/Hz requirements in addition modular design to accept brakes, encoders or pressured cooling.
High efficiency motor design available
Innovative self-locking, self-aligning taper shaft engine connection
Gearbox supplied factory filled with synthetic oil
Corrosion and shock resistant cast iron housing
High efficiency helical-bevel gears. 98% per stage
Normally closed breather with multiple places (Optional OtN2000)
Double lip seals upon heat treated, plunge ground shafts
Shaft mounting choices include tapered bushings designs
This is a comprehensive offering of energy-efficient, right angle helical bevel enclosed gearing. It really is available as gearmotors and a number of reducers with torque capacities up to 119,000 inch pounds. Housing styles include footed, face and flanged configurations. Gearmotors are available in three phase high efficiency styles through 50 HP and single phase to 5 HP. We provide a selection of input and result shaft choices. Additionally, you will find fixed and variable velocity motors and range of ratios available in this product offering.
Features
Accommodates insight power from ΒΌ Hp to 75Hp
Torque ratings up to 119,489 in-lbs
Decrease ratios up to 7,500:1
Helical – bevel – helical gear train offers affordable high and low speed solutions
Up to 94% efficient
Four input possibilities for all units
Two output flange choices – B5 and B14
Multiple output shaft interfaces
Critical dimensions interchangeable with main competitors
Modifications / Accessories
Integral Gearmotor
Clamp Collar C-Face Input
Solid Shaft Input
3-Piece Coupled C-Face Input
CEMA Screw Conveyor Adapter
EZ Kleen Washdown Package
XT Output Seals
Backstop
Heavy Duty Output Bearings
Inch or Metric Dimensions
Common Applications
Troughing Belt Conveyors
Slider Bed Conveyors
Mixer Drives
Screw Conveyors
Bucket Elevators
General Industrial Machinery
Common Industries
Aggregate and Cement
Air Handling
Chemical, Oil, and Gas
Food, Beverage, and Pharmaceutical
Paper and Forest
Unit and Baggage Handling
Water and Wastewater
As per the developing and varying needs of customers, you can expect an array of Helical Bevel Equipment Reducers. The technological content material of our products permits an extraordinary performance/lifespan ratio. The extremely versatile Helical Bevel Gear Reducers we offer are helical bevel gear reducer successfully used in a vast number of commercial and civil applications. These are B-Series units which offer excellent affordability and output torque/weight ratio, especially due to the fact they need very limited servicing. Besides these, our products are available in cast iron (sizes 063 to 163) or light weight aluminum (sizes A42 to A73) casing.
Features:
Sizes: 060-080-100-125-140-150-160
Available versions: B-fitted for electric motor coupling, IB with input shaft, CB with small motor, PB-fitted for engine coupling with flexible joint
Casing with foot FC, flange SC and general UC
Power up to 90 kW
Gears hardened and tempered with shaved or surface profile
Gearing with 3 reduction stages
Gleason spiral bevel gear pairs with run-in profile, mounted as second reduction stage for a higher resistance
Reduction ratios between 5, 71 and 187, 24
Torque max 13.000 Nm and admissible radial loads max 80.000 N
High-power casings optimized with FEM evaluation and input and output flanges of grey cast-iron G200 to ensure top level performances and high reliability
Load capacity calculated and verified according to ISO 6336 and AGMA 2001
Painted with RAL 5010 blue epoxy-polyester powder
Accessories: torque arm, result flange, result shaft, shrink disk, backstop device, protection cover kit, viton oil seals, reinforced result, assemble/disassemble kit
Series EP right angle helical bevel equipment motors offer ratios from 8:1 to 160:1 in three stages or up to 10000:1 in five levels. Motors can be found up to 90kW and output torque capability up to 12,300 Nm.
The series EP helical bevel gear motor was created with integral cast feet for base or end mounting and can be offered with single or dual extended output shafts.
Products are also available since shaft mounted or with output flanges and are designed for installation horizontally or vertically. The systems can also be provided with a bolt on torque reaction bracket and all variants can be found either motorised or with an insight shaft assembly.
Adding to the new range of Ever-Power helical equipment motors the product takes advantage of our a long time of accumulated design knowledge together with the use of high quality materials and elements. The end result is a number of acceleration reducing geared motors offering high load transporting capacities, increased efficiency, peaceful running and reliability.
Features of Helical Bevel Gear Motor
Standard motor connection
Capability to fit double essential oil seals, on insight and output shaft since required.
All models are dimensionally interchangeable with various other major manufacturers.
Units are manufactured and assembled from a family group of modular kits for distributor friendliness minimizing inventory and maximizing availability.
Motorized units can be fitted with a backstop module and reducer Products can be fitted with a backstop and fan.
Applications:
-Conveyors, Agitators, Elevators, Cranes, Crushers
-Helical Bevel gear motors are found in industries such as chemicals, pharma, packaging, food processing, plastic material and automation etc.
Key Features:
Sizes: A40-A50-A70
Obtainable versions: EP – fitted for electric motor coupling, IEP – with input shaft, CEP – with compact motor
Cases with ft, flange or universal
Power up to 4,8 Kw
Gears with shaved or floor profile
Gearing with 2 and 3 reduction stages
Hypoid bevel gears for size A40 and A50, gleason bevel gear pairs for size A70, all with run-in profile
Reduction ratios between 7,62 and 442,76
Torque max 450 Nm and admissible radial loads max 5.500 N on hollow shaft and 10.000 N on solid shaft
Cases in die-cast aluminium alloy
Exceptional mechanical strength while being and particularly lightweight
Load capacity calculated to ISO6336 and verified according to AGMA 2001-B88
Painted with RAL 5010 blue epoxy-polyester powder in in accordance to DIN 1843
Accessories: torque arm, output flange, output shaft.
Generallntroduction of HK series:
Gear Reducer
The EP series gear units, are novel transmission device and composed of Y series engine, helical gear,Arc gear and worm gear. The gears are made from high wear-resisting alloy components, specifically and finely processed.
Advantages:
1: Helical-bevel gear two-stage reducer
2: Compact structure, high efficiency
3: Quenched 20CrMnTi for gears
4: CE, ISO9001.
5: Compact design, small volume, good appearance ,and strong capacity to be overloaded.
6: Precise division and wide range for transmission ratio.
7: The efficiency is up to since high since 96% with low energy intake, strong adaptability and is capable of working continually in corrosive or damp environment.
8: All- purpose use, convenient and low-cost maintenance.
9: New seal gadget, strong adaptability.
10: Varied selection of motor combinations, mouting positions and struture projects.