Worm drive gearbox with motor
A robust worm-drive gearbox powered by an MM28 engine. Ideal applications where an easy to match, high torque output is required. Ideal for student based projects which includes worm motor robots and buggies.
The machine has been designed to ensure that the output shaft could be ‘clicked’ in and out for modification. E.g. reducing to size. The electric motor is snap installed into its cradle to engage the apparatus and worm.
Details
1 – 6V DC
0.1A to 1A based on load
Driveshaft length: 12.5cm
Driveshaft diameter 3mm
Gearbox ratio: 42:1
General dimensions of box + motor: 35(W) x 40(H) x 60(L)mm
The primary feature of the high-efficiency gear box is a worm gear, which locks the output shaft whenever the electric motor isn’t turning. The high equipment ratios of 216:1 or 336:1 make this gearbox appropriate for small walking robots, lifting mechanisms, and additional applications where high torque is definitely desired.
The low-voltage motors in the worm gearbox run on 1.5-4.5 volts and draw up to a few amps, making them ideal candidates for the DRV8833 motor driver carrier. Motor overheating can be caused by excessive stalling, actually at very low voltages. We recommend that you utilize stall-detection sensors, or just view your robot, to ensure that it doesn’t stall for more than a few seconds at a time.
This gearbox includes a 4 mm diameter, round output shaft, which works with the wheels that are compatible with Tamiya 4 mm, round shafts. Our 3 mm universal installation hub also matches on the smaller threaded end of the shaft, though it is not specifically intended to work with this kind of shaft (the hub’s set screw could harm the thread on the shaft).
Ever-Power equipment motors are economical, right-angle, worm-geared motors that install easily in the tightest applications. Economical right angle worm geared motors arranged new standards for reliability, efficiency and economic climate with unparalleled features including hollow shafts in the smallest sizes. An inverter friendly design offers easy integration today and a truly future proof remedy. The Ever-Power gear electric motor offers total versatility in mounting choices includes shaft, base, encounter, and flange solutions. The motor terminal box could be mounted in alternative positions rotated in 90º steps around the electric motor frame offering for unparalleled integration options.
Ever-Power gear motors comply with UNITED STATES and International criteria, including NEMA, IEC, CSA, and CE, the Ever-Power series permits worldwide acceptance, a genuine total solution for our global customers.
Excellent protection of IP65 acc. to IEC 529 assures you that the Ever-Power series is dirt tight and hose evidence,and can be utilized outside or in wet and dusty conditions without the usage of additional enclosures. Full rated output is offered by the output shaft of the unit.
Product Features
Power rating up to 5,5 kW.
Torque 25 … 1.000 Nm
Output Speeds 0,2 … 300 min-1
versatile installation possibilities
Totally enclosed, sealed against dust and water spray
Lubrication change initial after 15000 hrs
Low noise gearing
Mains connection 110 … 690V, 50/60Hz
Enclosure IP65 (Regular), IP66 (Optional)
Additional features:
Connecting with Connect connectors.
With integrated inverter up to 7,5kW.
Ever-Power-Mark
CSA, UL, ATEX, GOST, CCC, ISO9001, ISO14001, OHSAS18001
Motors according to EN 60034
Corrosion category based on DIN ISO 12944-5
C1, C2, C3, C4, C5-We, C5-M
DC WORM GEAR MOTORS
Ever-Power DC worm equipment motors are the option for applications requiring a corner turn, optional dual result, or an inability for the electric motor to be back again driven. The DC correct angle equipment motors are made for continuous and intermittent duty operation. Our right angle equipment reducers are designed with several mounting plate choices, making them ideal for a number of DC motor based applications. You can expect 12 ratios ranging from 5:1 to 100:1.
10309
FEATURES
1/43 to 3/8 HP
12, 24, 90, 130, 180 VDC, 115 FWR
9 – 475 RPM
1.5 – 315.9 in-lb rated torque
Frame Size 60, 80, 108 mm
5:1 – 100:1 standard ratios
Regular brush life of 2000+ hours (varies by application)
EP Products Worm Equipment Motors are created to generate high torque in a small package size. Worm Equipment Motors are great for applications that want a self- locking or breaking feature since the output shaft can’t rotate when there’s no power applied. Additionally, Worm Gearheads can transfer movement in 90 degrees. With various decrease ratios, precision cut gears, voltages and sizes, EP Products has a DC Worm Gear Motor solution for the application.
Features and Benefits
HIGH Torque Capabilities
Self-Locking / Braking Features
Motion Transfer of 90 Degrees
Ability to Handle Large Gear Reduction Ratios
High Durability
Low Noise
Flexible Configuration
Applications
Protection Door Locks / Industrial Conveying Systems / Security Gates / Teeth Seats / Ambulance Cots & Stretchers Quite a few DC Motors can be complimented with among our Worm Gearheads. EP Items will continue to work with you to create and produce a Worm Gear Engine which will optimize the functionality of your specific application.
Built to your unique requirements
Electric motor Type: Brushed / Brushless / Coreless
Voltage
Output Speed
Power
Current
Torque
Reduction Ratio
Shaft Material & Size
Gear Material
Shaft Configuration: (D Cut / Round / Splined / Other)
Overall Size Parameters (L, W, H)
Encoder Type: Optical / Hall Effect
Extra Assembly Requirements (lead wires, connectors, etc.)
INTRODUCTION
The turbo metal gear worm electric motor runs on the metal gear box for durability and a higher torque output. Due to the special mechanical structure of the worm drive the electric motor output shaft can be self locking and can not be rotated.
This part runs on the two wire connection and supports direction control in addition to PWM speed control. Rated voltage is 12v and will obtain 40RPM, with a torque of 8kg/cm.
SPECIFICATION
Operating Voltage: 6 – 15 V
Rated Voltage: 12V
No-load Speed: 40 RPM
No-load Current: 35 mA
Rated Torque: 32 RPM
Rated Current: 180 mA
Ranked Torque: 2.2 kg.cm
Rated Power: 1.1 W
Stall Torque: 8 kg/cm
Stall Current: 1 A
Reduction Ratio: 1:150
Weight: 167 g
EP Geared Motors with Worm Gearing – Modual & Customizable drive technology
Worm gear products from EP DRIVESYSTEMS especially display their strength in applications where high gear ratios are essential. Our worm geared motors are therefore optimally suited for use in intralogistics, packaging technology and the food & beverage industry.
Four great known reasons for EP worm geared motors:
Rugged
Our worm geared motors have a higher overload capacity
Maintenance Friendly
Washdown versions enable simple and effective cleaning of the drive program.
Corrosion protection
The NSD tupH sealed surface area conversion is exceptionally chemical, corrosion and abrasion resistant.
Flexibility
Our modular design give users maximum freedom.
The modular system for maximum flexibility: Our EP worm gear units
There are numerous applications that require drive systems, and each of these has its unique requirements. The EP series worm equipment motors could be quickly and efficiently adapted to fulfill your needs.
Worm gear devices impress with their high power density and compact style. If required, we can also supply them with the impressive nsd tupH surface treatment.
In addition to the basic EP casing, you can expect an extensive type of bolt-on components to customize the product including torque arms, shaft covers and output flanges. These can be easily field installed, but we may also be happy to assemble the average person components for you.
Discover more about our modular SI worm geared motors!
Find out more
Simple and Clean: The EP worm gear unit SMI
SMI worm gear units feature a easy, corrosion-resistant alluminum alloy housing. Optional nsd tupH surface conversion makes this product ideally suited for severe and demanding industries like food processing and pharmaceuticals.
Flexible input designs such as NEMA, IEC or direct motor mounts in additional foot or flange mounted housing designs.
Worm geared motors
Worm geared motors for little power range.
The WATT small worm gear unit adapt themselves concerning UNIBLOCK design optimally in the geared motor program. The units have on all sides different repairing possibilities and enable a simple assembling for the customer.
Additional drive configurationscan be created by use of built-on accessories (e.g. torque arm and result flanges). The housings are made in light weight structure out of aluminium die cast. Electric motor attachment is realised in general by means of IEC adapter B5 or B14A.
Technical Data
Number of sizes:5
Power Range:0.12 – 2.2kW
Output torque range:17 – 230Nm
Ratio:5 – 100
Output option:output shaft, output shaft on both sides, hollow shaft, hollow shaft with shrink disc
Assembly/mounting:uniblock, flange, torque arm
Buy Worm Drive Gearbox with Electric motor – incorporating the following features: 1 to 6V voltage ranking, 17100 rpm simply no load swiftness, 220g-cm stall torque, 3mm shaft diameter, 60mm long, 35mm wide, 40mm high, a robust worm drive gearbox powered by an MM28 electric motor (included), most ideal for applications where an easy to match, high torque result is necessary, nylon housing and gear, requires light essential oil or silicon grease lubrication, perfect for student based tasks including robots and buggies.
Most suitable for applications where a simple to match, high torque result is required
Perfect for student based projects including robots and buggies
Reversible High torque Turbo Worm Gear Engine JGY370 DC 12V 40RPM
Reversible High torque Turbo Worm Gear Engine JGY370 DC 12V 40RPM
Features:
The engine is Gear DC engine with micro-turbine worm, you can change the wiring-connection to change motor rotation.
Turbo worm geared motor with self-lock, that’s, in the case of motor without electric, the output axis is usually fixed, self-lock.
The reducer output shaft arranged vertically with the engine shaft, whole engine output shaft relatively-short than general gear motor, trusted to be installed the dimensions requirements strictly occasion.
Specifications:
Model: JGY370
Voltage: DC12V
No load speed: 40r/min
Output torque: 5.6kg.cm
Rated current: 0.06A
Weight: 163g
Application: open the screen, door, Mini winch. Ect.
In sumo robot or combat robot competition where high holding torque’s engine is essential to avoid your robot being pushed by your opponent robot. The worm gear is certainly a better option compared to the spur gear motor. Why is worm gear so unique? Take a look wiki out: Worm Drive.
“Unlike with ordinary gear trains, the path of transmission (input shaft vs output shaft) isn’t reversible when working with large reduction ratios, because of the higher friction involved between the worm and worm-wheel, when usually a single start (one spiral) worm is used. This is often a advantage when it is desired to get rid of any probability of the result driving the input.”
In other terms, it is difficult to push your load (example, your robot) if the motor isn’t power or rotate.
Features and Spec:
Metal gear box
Result shaft is self-locking because of the worm gear’s characteristic
Rated voltage: 12V DC
Rated output speed: 150 RPM
Rated output torque: 117mN.m (1.2kgf.cm)
Stalled torque: 196mN.m (2kgf.cm)
No load current: 60mA
Stalled current: 1.8A
Output shaft diameter: 6mm with 4.5mm slot
Weight: 150g